How To Apply Tile Adhesive At Home? Step By Step Guide

Learn More

Arrow

How To Apply Tile Adhesive At Home?

If you're doing your own tile installation, we'll teach you how to properly mix and apply tile glue for a clean and professional finish, as well as how to calculate how much adhesive you'll need.

How To Apply Tile Adhesive At Home?

If you're familiar with intermediate DIY projects, you can tile your bathroom or kitchen walls yourself. After you've prepped your wall for tiling, you'll need to calculate how much tile adhesive you'll need before properly mixing and applying it.

How To Apply Tile Adhesive At Home?

This will guarantee that your tiles are mounted to your wall safely and securely.

How To Use It?

Before beginning your ceramic tile project, we recommend that you familiarise yourself with the major methods and instruments required to complete the task professionally. 

How To Use It?

As a result, you must understand how to spread the glue for tile floors and walls in order to disperse it in an even layer throughout the whole surface; otherwise, the tiles may become free from the adhesive. 

How To Use It?

Before distributing the thin set, you must first prepare the subfloor. Fill the crevices and vacuum the residues and other particles as a result.

How To Use It?

Additionally, use a big level to ensure that the floor is absolutely horizontal.  If necessary, a small coating of self-levelling material must be poured to make it horizontal.

How To Spread The Tile Adhesive?

Using a drill and a paddle, combine the tile glue in a clean bucket. You can, however, mix the thin-set by hand using a margin trowel. 

How To Spread The Tile Adhesive?

Before applying tile adhesive on the floor, check sure there are no lumps and that the consistency is correct. Load the trowel with material and check if it falls.  If it stays on the notched trowel yet can be spread over the floor, it signifies it has the proper consistency.

How To Spread The Tile Adhesive?

 Load the notched trowel with tile glue using a margin trowel or a palette knife. Work with extreme caution and, if your skin is sensitive, wear gloves. Spreading glue is a dirty operation, so put on some old clothing beforehand.

How To Spread The Tile Adhesive?

You don't need to load the trowel with too much material (what you see in the image is plenty); otherwise, it will be difficult to distribute it on the wall or floor.

How To Spread The Tile Adhesive?

Then, apply the glue on the surface with the trowel's straight edge. Hold the trowel at a 45° angle and slide it back and forth numerous times until the glue bed is generally level.

How To Spread The Tile Adhesive?

Then, using the notched edge of the trowel, comb the tile adhesive. Remember to keep the trowel tilted at around 45° otherwise, the ridges will be too thin. 

How To Spread The Tile Adhesive?

Continue until the entire area is coated with an equal layer of tile adhesive. Work slowly and add more glue to the floor as needed. After that, place the tiles on the adhesive and tap them into place with a hammer. If you strike the tiles too hard, you risk harming them. To achieve regular joints, use spacers between the floor tiles.

How To Spread The Tile Adhesive?

In these cases, the best method is to apply glue directly to the back of the tiles. To complete the task like a professional, comb the glue with the notched trowel.

How To Spread The Tile Adhesive?

Last but not least, tile adhesive should be applied to a wall using the same ways discussed above. Just be patient and don't apply the adhesive to a greater surface than necessary. Make careful to comb the glue using a trowel's notched edge. Check the ridges for evenness before putting the wall tiles.

Materials Required

- Buckets Adhesive - The mixing paddle (can be bought from most hardware stores) - Trowel with a notch

Materials Required

– Personal protection equipment (eyewear, facemask, gloves) – Spacers – Water You won't need a bucket, mixing paddle, or water if you use ready-mixed glue.